进口塑胶料
注:请在右边的搜索栏查找产品

PBT 771 Resin 阻燃,含15%玻纤和20%矿物增强

添加时间:2014-03-26  信息来源:http://www.kingoflotto.com/  作者:苏州希普能塑料
VALOX PBT 771 Resin
VALOX™ PBT 771 Resin
15%玻纤,20%矿物填充
聚对苯二甲酸丁酯
SABIC Innovative Plastics (Europe-Africa-Middle East)
 
产品说明
VALOX 771 is a 15% glass and 20% mineral filled, flame retarded injection moulding PBT resin.
 
增强填料:含15%玻纤和20%矿物增强
材料特点:阻燃
定属记号:PBT
塑料牌号:PBT 771
加工方法:注射成型
销售电话:185 5121 3137 谭经理
湘樟专卖:http://www.kingoflotto.com/sujiao/pbt/valox/771-resin.html
 
材料物性
MECHANICAL Value Unit Standard
Tensile Stress,yld,Type I,5 mm/min 860 kgf/cm² ASTM D 638
Tensile Stress,brk,Type I,5 mm/min 860 kgf/cm² ASTM D 638
Tensile Strain,yld,Type I,5 mm/min 2 % ASTM D 638
Tensile Strain,brk,Type I,5 mm/min 2 % ASTM D 638
Tensile Modulus,5 mm/min 96800 kgf/cm² ASTM D 638
Flexural Stress,yld,1.3 mm/min,50 mm span 1120 kgf/cm² ASTM D 790
Flexural Stress,brk,1.3 mm/min,50 mm span 1120 kgf/cm² ASTM D 790
Flexural Modulus,1.3 mm/min,50 mm span 80500 kgf/cm² ASTM D 790
Taber Abrasion,CS-17,1 kg 55 mg/1000cy SABIC Method
Tensile Stress,yield,5 mm/min 85 MPa ISO 527
Tensile Stress,break,5 mm/min 85 MPa ISO 527
Tensile Strain,yield,5 mm/min 2 % ISO 527
Tensile Strain,break,5 mm/min 2 % ISO 527
Tensile Modulus,1 mm/min 9700 MPa ISO 527
Flexural Stress,yield,2 mm/min 120 MPa ISO 178
Flexural Stress,break,2 mm/min 120 MPa ISO 178
Flexural Strain,break,2 mm/min 2 % ISO 178
Flexural Modulus,2 mm/min 8400 MPa ISO 178
Hardness,H358/30 120 MPa ISO 2039-1
Hardness,Rockwell R 111 - ISO 2039-2
IMPACT Value Unit Standard
Charpy Impact,unnotched,23℃ 29 kJ/m² ISO 179/2C
Charpy Impact,unnotched,-30℃ 29 kJ/m² ISO 179/2C
Izod Impact,unnotched,23℃ 39 cm-kgf/cm ASTM D 4812
Izod Impact,unnotched,-30℃ 39 cm-kgf/cm ASTM D 4812
Izod Impact,notched,23℃ 5 cm-kgf/cm ASTM D 256
Izod Impact,notched,0℃ 5 cm-kgf/cm ASTM D 256
Izod Impact,notched,-30℃ 5 cm-kgf/cm ASTM D 256
Izod Impact,unnotched 80*10*4 +23℃ 25 kJ/m² ISO 180/1U
Izod Impact,unnotched 80*10*4 -30℃ 25 kJ/m² ISO 180/1U
Izod Impact,notched 80*10*4 +23℃ 5 kJ/m² ISO 180/1A
Izod Impact,notched 80*10*4 0℃ 5 kJ/m² ISO 180/1A
Izod Impact,notched 80*10*4 -30℃ 5 kJ/m² ISO 180/1A
Charpy 23℃,V-notch Edgew 80*10*4 sp=62mm 4 kJ/m² ISO 179/1eA
Charpy Impact,notched,23℃ 6 kJ/m² ISO 179/2C
Charpy -30℃,V-notch Edgew 80*10*4 sp=62mm 4 kJ/m² ISO 179/1eA
Charpy Impact,notched,-30℃ 6 kJ/m² ISO 179/2C
Charpy 23℃,Unnotch Edgew 80*10*4 sp=62mm 45 kJ/m² ISO 179/1eU
Charpy -30℃,Unnotch Edgew 80*10*4 sp=62mm 20 kJ/m² ISO 179/1eU
THERMAL Value Unit Standard
Vicat Softening Temp,Rate A/50 220 ASTM D 1525
Vicat Softening Temp,Rate B/50 190 ASTM D 1525
HDT,0.45 MPa,3.2 mm,unannealed 220 ASTM D 648
HDT,1.82 MPa,3.2mm,unannealed 203 ASTM D 648
CTE,-40℃ to 40℃,flow 2.25E-05 1/℃ ISO 11359-2
CTE,-40℃ to 40℃,xflow 5.9E-05 1/℃ ISO 11359-2
CTE,23℃ to 80℃,flow 3.E-05 1/℃ ISO 11359-2
CTE,23℃ to 80℃,xflow 9.5E-05 1/℃ ISO 11359-2
CTE,23℃ to 150℃,flow 3.01E-05 1/℃ ISO 11359-2
CTE,23℃ to 150℃,xflow 1.35E-04 1/℃ ISO 11359-2
Ball Pressure Test,125℃ +/- 2℃ PASSES - IEC 60695-10-2
Vicat Softening Temp,Rate A/50 220 ISO 306
Vicat Softening Temp,Rate B/50 190 ISO 306
Vicat Softening Temp,Rate B/120 190 ISO 306
HDT/Be,0.45MPa Edgew 120*10*4 sp=100mm 215 ISO 75/Be
HDT/Ae,1.8 MPa Edgew 120*10*4 sp=100mm 190 ISO 75/Ae
HDT/Bf,0.45 MPa Flatw 80*10*4 sp=64mm 220 ISO 75/Bf
HDT/Af,1.8 MPa Flatw 80*10*4 sp=64mm 190 ISO 75/Af
Relative Temp Index,Elec 120 UL 746B
Relative Temp Index,Mech w/impact 125 UL 746B
Relative Temp Index,Mech w/o impact 140 UL 746B
PHYSICAL Value Unit Standard
Specific Gravity 1.7 - ASTM D 792
Filler Content 35 % ASTM D 229
Mold Shrinkage on Tensile Bar,flow(2)(5) 0.3-0.6 % SABIC Method
Mold Shrinkage on Tensile Bar,xflow(2)(5) 0.4-1 % SABIC Method
Melt Flow Rate,266℃/5.0 kgf 20 g/10 min ASTM D 1238
Density 1.7 g/cm³ ISO 1183
Water Absorption,(23℃/sat) 0.94 % ISO 62
Moisture Absorption(23℃/50% RH) 0.09 % ISO 62
Melt Volume Rate,MVR at 250℃/5.0 kg 8 cm³/10 min ISO 1133
Melt Volume Rate,MVR at 265℃/5.0 kg 16 cm³/10 min ISO 1133
Melt Viscosity,260℃,1500 sec-1 140 Pa-s ISO 11443
ELECTRICAL Value Unit Standard
Volume Resistivity >1.E+15 Ohm-cm ASTM D 257
Arc Resistance,Tungsten{PLC} 4 PLC Code ASTM D 495
Hot Wire Ignition{PLC) 0 PLC Code UL 746A
High Voltage Arc Track Rate{PLC} 0 PLC Code UL 746A
High Ampere Arc Ign,surface{PLC} 0 PLC Code UL 746A
Volume Resistivity >1.E+15 Ohm-cm IEC 60093
Surface Resistivity,ROA >1.E+15 Ohm IEC 60093
Dielectric Strength,in oil,1.6 mm 23 kV/mm IEC 60243-1
Dielectric Strength,in oil,3.2 mm 20 kV/mm IEC 60243-1
Relative Permittivity,1 MHz 3.1 - IEC 60250
Dissipation Factor,50/60 Hz 0.009 - IEC 60250
Dissipation Factor,1 MHz 0.012 - IEC 60250
Comparative Tracking Index 600 V IEC 60112
Comparative Tracking Index,M 175 V IEC 60112
Relative Permittivity,50/60 Hz 3.3 - IEC 60250
FLAME CHARACTERISTICS Value Unit Standard
UL Recognized,94V-2 Flame Class Rating(3) 0.62 mm UL 94
UL Recognized,94V-0 Flame Class Rating(3) 0.75 mm UL 94
UL Recognized,94-5VA Rating(3) 2 mm UL 94
Glow Wire Flammability Index 960℃,passes at 1 mm IEC 60695-2-12
Glow Wire Ignitability Temperature,1.0 mm 675 IEC 60695-2-13
Glow Wire Ignitability Temperature,2.0 mm 675 IEC 60695-2-13
Glow Wire Ignitability Temperature,3.0 mm 775 IEC 60695-2-13
Oxygen Index(LOI) 31 % ISO 4589
Injection Molding Value Unit
Drying Temperature 110-120
Drying Time 2-4 hrs
Maximum Moisture Content 0.02 %
Melt Temperature 250-270
Nozzle Temperature 240-260
Front-Zone 3 Temperature 245-265
Middle-Zone 2 Temperature 240-255
Rear-Zone 1 Temperature 230-245
Hopper Temperature 40-60
Mold Temperature 40-100
PBT VALOX™ RESIN
Semi-crystalline polybutylene terephthalate, one of the most widely-used engineering materials, shows low moisture and thermal expansion and offers outstanding wear and friction properties. With good strength at high temperatures, it has good electrical properties and flame resistance.
联系湘樟塑料
相关材料